Description:

(*IN PLANT ROLE -See Client specific information below in Job Requirements)

Summary of Description:

Perform limited tasks and calculations necessary for engineering and design efforts supporting construction drawings and packages under the guidance of a supervising engineer.

Duties:

Checking drawing packages and vendor submittals for completeness and accuracy.
Convey adequate instructions to enable the design staff to perform their task with quality work.
Perform calculations for related discipline under the direction and supervision of an experienced engineer.
Perform other job-related duties as assigned.

Education and Experience:

Bachelor of Science Degree in a related discipline from an accredited university with 0-2 years of experience in refinery, petrochemical, chemical, offshore, pipeline or utility industries; or an equivalent combination of education and experience sufficient to successfully perform the essential duties of the job such as those listed above.

License Requirements:

Valid Driver's License as per State law or requirement

Engineer Intern (E.I.) certification preferred

Specific Skills:

AutoCAD experience preferred.

Basic computer skills Microsoft Office and Outlook or similar software.

Knowledge of regulatory codes and requirements for the related discipline preferred.

Understanding of basic engineering principles and application.

Physical Requirements:

Ability to walk up to one mile on industrial plant and construction sites outdoors at any time of the year.

Ability to work in protective clothing which may elevate body temperatures by several degrees Fahrenheit for periods of up to 15 minutes without a break.

Ability to use multi-level stair towers and rung ladders unassisted.

Ability to hear safety alarms and signals while wearing hearing protection.

Ability to sit at desk and operate computer for extended periods of time.

Ability to stand, use hands and fingers, grip, handle or feel; reach with hands and arms; climb or balance; stoop, kneel, crouch or crawl; and talk and hear.

Ability to see with visual acuity and distinguish between colors.

Ability to operate a motor vehicle and have a valid driver's license.

Ability to lift and carry 15 lbs. on a regular basis is required and at times lifting up to 25 lbs. may be required.

Requirements:

*Due to in plant position the below referenced Job Duties have been provided by client:

Summary:

The primary responsibility of the process engineer is to provide technical support as a technical expert, conducting process analysis, troubleshooting and design for the site's units in order to sustain and improve profitability, while maintaining a strong commitment to safety and environmental compliance. This position requires daily interaction with operations, technical, safety, maintenance and reliability to drive overall improvements in unit performance. This role will lead the design and installation of long-term projects to overcome process constraints, resolve reliability issues and comply with environmental regulations. This will include defining scope, providing front-end-loading and incorporating process knowledge during engineering phases. This role will also advise on initiatives to maintain a competitive advantage. The Process/Production Engineer will monitor, troubleshoot, and optimize operating units to drive process and product improvements. During a typical day they will apply technical knowledge to detect causes of deviations in quality, capacity, yield, and energy consumption.

Responsibilities:

Collaborates with operations to identify new opportunities to remove constraints to maximize on stream time and profitability while ensuring safe, environmentally complaint, reliable operations
Analyzes complex operating issues and provides documented recommendations to improve performance
Leads capital, expense and special project scope development, execution, support and training
Leads Management of Change process (MOC/PSSR)
Provides technical expertise in process safety including, PHAs, PSVs, safety system bypasses, and other PSM activities in the area
Provides technical expertise during troubleshooting, turnarounds, startups, shutdowns, catalyst changes and other non-routine unit activities
Reviews engineering calculations to quantify environmental impacts and releases
Advocates and drives improvements in safety and environmental performance
Participates on cross-functional improvement teams within the site
Maintains strong safety and environmental compliance focus
Monitors, troubleshoots and optimizes operating units
Contributes in a team environment and establishes work relationships with onsite and offsite functional groups to achieve results
Balances day-to-day operational priorities with long term strategic objectives to ensure alignment with company goals
Supports gap closure and continuous improvement activities by providing technical expertise, engineering calculations, and justifications for new projects and participating in capital, expense and special project scope development, execution, support and training
Develop new and enhance existing management systems and procedures to quantify and compare operating performance with established standards and assures compliance with existing standards
Determines causes of deviations in quality, capacity, yield, and energy consumption
Collaborates with operations to identify new opportunities to remove constraints to maximize on stream time and profitability while ensuring safe, environmentally compliant, reliable operation
Analyzes complex operating issues and provides documented recommendations to improve performance
Develops and manages KPI

PIf0eafa6c25f9-25826-34886064

Recon Management Services

New Jobs

P6 Scheduler (Technician II)

Process Production Engineer (Engineer I)